Telescope eyepiece calculator
Magnification = telescope focal length ÷ eyepiece focal length. A 1,200 mm telescope with a 10 mm eyepiece gives 120×, an exit pupil of 1.7 mm (aperture ÷ magnification) and, with a 52° eyepiece, a true field of about 26 arcminutes, a little less than the width of the full Moon. Enter your own telescope below to see the same numbers, plus the useful power range and what will fit in the eyepiece.
The four numbers that matter
Magnification makes things bigger, but it also makes them dimmer and magnifies the shimmer of the atmosphere.
Exit pupil is the simplest way to judge an eyepiece for your telescope: it combines aperture and focal ratio into one number that predicts how bright and how sharp a view will feel.
True field is how much sky you see. It decides whether the whole Pleiades or the whole Moon fits.
Useful range is set by aperture: roughly aperture ÷ 7 at the low end (your eye's pupil) and aperture × 2 at the top.
Not sure what to buy? The eyepiece set planner turns these rules into a shopping list for your focal length.
Eyepieces in a 1,200 mm, 200 mm telescope
This is the classic 8-inch f/6 Dobsonian. The same table works for any 1,200 mm telescope; only the exit pupil column changes with aperture. Pick your own scope from the list in the calculator to compare.
| Eyepiece | Magnification | Exit pupil | True field (52° eyepiece) | Good for |
|---|---|---|---|---|
| 40 mm | 30× | 6.7 mm | 1.73° | Finding, widest deep-sky views |
| 32 mm | 38× | 5.3 mm | 1.39° | Finding, widest deep-sky views |
| 25 mm | 48× | 4.2 mm | 1.08° | Finding, widest deep-sky views |
| 20 mm | 60× | 3.3 mm | 52′ | Clusters, galaxies, the whole Moon |
| 15 mm | 80× | 2.5 mm | 39′ | Clusters, galaxies, the whole Moon |
| 12 mm | 100× | 2 mm | 31′ | Clusters, galaxies, the whole Moon |
| 10 mm | 120× | 1.7 mm | 26′ | Moon detail, planets on most nights |
| 8 mm | 150× | 1.3 mm | 21′ | Moon detail, planets on most nights |
| 6 mm | 200× | 1 mm | 16′ | Moon detail, planets on most nights |
| 5 mm | 240× | 0.8 mm | 13′ | Planets and doubles on steady nights |
| 4 mm | 300× | 0.7 mm | 10′ | Planets and doubles on steady nights |
How to use the results
- Start low. Find the target with the eyepiece giving the biggest exit pupil (4–6 mm). The supplied 25 mm or 32 mm eyepiece usually does this.
- Step up in roughly 1.5× jumps. 48× → 80× → 120× → 200× is a sensible ladder in a 1,200 mm scope. Smaller jumps show little difference.
- Stop when the image stops improving. If detail goes soft and wobbly, the air is the limit, not the eyepiece. Go back one step.
- Check the field. If something does not fit (the Pleiades, the Andromeda galaxy), you need a longer eyepiece or one with a wider apparent field. See true field of view.
More calculators
- Eyepiece set planner
Which three or four focal lengths to buy for your telescope.
- Magnification for planets
Jupiter, Saturn, Mars and the Moon, by aperture and seeing.
- Barlow lens calculator
What a 2× or 3× Barlow does to power, exit pupil and field.
- Aperture chart
Resolution, faintest stars and useful power for 50–400 mm.
Questions people ask
How do I work out my telescope's magnification?
Divide the telescope's focal length by the eyepiece's focal length, both in millimetres. A 1,200 mm telescope with a 25 mm eyepiece gives 1200 ÷ 25 = 48×. With a 2× Barlow it becomes 96×.
What is the highest magnification my telescope can use?
About twice the aperture in millimetres (50× per inch) on a perfect night, so 140× for a 70 mm scope or 400× for 200 mm. On most nights the air limits any telescope to roughly 150–250×.
What does the exit pupil tell me?
How wide the beam of light leaving the eyepiece is. Around 4–6 mm gives bright, wide deep-sky views; 2–3 mm is a general-purpose middle; 0.7–1 mm shows the most planetary detail. Above about 7 mm your eye cannot take all the light.
Is a higher magnification eyepiece always better?
No. Every doubling of magnification spreads the light over four times the area, so the view gets dimmer and softer once you pass what the aperture and the air can support. Most observing happens below 150×.
Where do I find my telescope's focal length?
It is usually printed on a label near the focuser or on the front of the tube as “D = 130 mm, F = 900 mm”. D is the aperture and F the focal length. The focal ratio (f/6.9 here) is F ÷ D.
Formulas: magnification = telescope focal length ÷ eyepiece focal length; exit pupil = aperture ÷ magnification; true field = field stop ÷ focal length (in radians) or, approximately, apparent field ÷ magnification; Dawes limit = 116 ÷ aperture in mm (arcseconds). Limiting magnitude uses the common rule of thumb 2.7 + 5·log₁₀(aperture in mm) for an experienced observer under a dark sky. Planet sizes are typical yearly ranges from published ephemerides.